10 Healthy Kia Picanto Key Fob Replacement Habits

How to Replace a Kia Sportage Replacement Key

The key on many Kia models has the keyless entry feature built into. This key usually resembles an electronic remote and can be changed with a new one from an Kia dealer or locksmith.

Key fobs might stop working due to a number of reasons, such as a dead battery, worn-out buttons signal interference or water damage. Here are some helpful tips to assist you in getting your Kia sportage replacement key to work once more.

How do you replace the remote key or smart key?

The battery inside your Kia's smart key will eventually have to be replaced, regardless of whether it's a remote key that starts with a push button or a normal metal key that doesn't have transponder. This is especially in the event that your car displays a message indicating that the smart key or remote has low battery power.

It's a simple process. To replace the keyfob battery remove the mechanical key from the slit that is located at the back of the fob. Then, pry the cover off. A small screw will be found inside the key fob that holds the battery in its place. Remove the old battery by removing the screw using a small screwdriver. Insert the new battery and close the slit on the key fob.

When the key fob is equipped with a fresh battery, test it by pressing the lock and unlock buttons. You're good to go if the doors lock and unlock as expected. You can now take advantage of the hands-free lock/unlock feature on your Kia when your fingers start to get cold or you have to make errands in Brandon.

Note: Certain key fobs (transponder chip or smart keys) might require their programming completed. This requires a special programming machine that only the dealer or locksmith has access to. Other keys (non-transponder metal keys) do not require programming. If you want to change the programming of your key, it is necessary to note the key code number on the tag for the key code.

How do you replace a dead battery?

If the Kia key fob does not respond to pressing the lock/unlock button, it is most likely that the battery is not fully charged. A weak battery could cause other issues, like the check engine light flashing or the engine not cranking correctly. It is fairly easy to replace the key fob batteries by using only some tools.

Before you begin the process before beginning the process, ensure that your vehicle is off and all doors are closed. Find the small metal or plastic piece that is on the bottom of your key fob and move it until a metal key pops out. You can then put the key into the door handle of the driver to unlock your car.

To replace the key fob's battery, remove the rear cover and use a pry bar tool to release the latch that holds the black negative battery cable. Remove the old battery and then orient the new battery so that the "+" positive side is facing your face and the "-" negative side is facing towards the fob's electrical contacts made of metal. Push the new CR2032 battery straight into position, avoiding excessive force to avoid damaging or bending the contacts of the metal.

Once the new battery has been installed and the key fob is turned on, turn it off and then turn it on in the ignition several times until the door locks. Then, you can test your kia ceed key fob programming key fob to see if it is working properly again.

How to replace a smart keys

Depending on the model of your Kia Sportage, you may have a standard key fob or a smart key. The smart key comes with an embedded mechanical key blade, however, the standard key fob does not. Both key fobs come with batteries that eventually require changing. It's a fairly simple process that takes just two minutes.

Be sure to switch off your Kia, and be on a flat, well-lit surface before you begin. Be aware that there are tiny parts inside the fob that could be removed if not careful.

The first step is to locate the small release button that is located on the back of the lower part of the fob. It could be a circular button or rectangular slot. You can open the key fob by pressing the button.

Once you have the key fob opened, you can simply remove the old battery and replace it. The new battery is a one called CR-2032 and can be bought online or in your local auto parts shop. After you've finished, your key fob should permit you to lock and unlock your vehicle even if it's not running.

How do I replace the mechanical key?

The Kia key fob is a great option that lets us lock and unlock our car key Duplication Service with the click of the button. Like any other device it is possible that the Kia key fob may have issues. There are steps that can be taken to fix these issues and keep our key fobs in good working order for the long run.

A low or dead battery is one of the most common problems. This can cause your fob to stop working or work intermittently. If this is the case, try replacing the battery with a new one.

If this does not resolve the issue, use the flathead screwdriver that is standard to push the plastic casing of the fob open. Be careful not to damage internal components or scratch the plastic. After opening, carefully remove the battery that was removed and replace it with a brand new one.

After the new battery has been put installed, close and unlock the doors using the mechanical key (every Kia fob comes with an emergency mechanical key that will fit into the slot). Test the key fob to make sure it is working correctly. Contact a dealer or a locksmith to address the issue in the event that the key fob is not working. Make sure they make you an emergency key that functions for all door and trunk cylinders to prevent lockouts in the future.